Tank Bolts have been shown to be long-lasting, and the 5/16" x 2 3/4" length will suit most brands and models. The bolts can be used on all metal tanks (not just PEX) and they can be installed from both sides of the tank. They can also be removed by hand in case of an emergency.
There are two types of Tank Bolts: compression-type and expansion-type. Both work by using a washer and nut to hold the tank down to the bowl. The only difference is that the expansion bolt has a hollow center and is covered with rubber or another elastic material, which allows it to expand when tightened down over a pipe or other object.
This article focuses on compression-type tank bolts. These bolts use a washer and nut to hold the tank down to the bowl. On older homes with steel tanks, compression-type bolts are usually made of brass or stainless steel and measure 5/8" or 3/4" in diameter. These bolts go through the floor first and then into the tank. They are easy to install and remove without any tools needed.
Modern homes with PEX water tanks often use plastic compression-type bolts that are either coated in stainless steel or colored black.
2 1/4" is the standard length for Johni-Bolts. They are also available in an extra-long (3 1/2 inch) length. To determine the proper bolt length, divide the overall height of your toilet by two plus its diameter. Example: If your toilet is 3 feet high, then you'll need a bolt that is at least 6 inches long.
The torque value listed on toilet bolts varies depending on the make of the bolt. However, most toilets require 20 foot pounds of torque to secure them properly. Larger bolts typically require more torque to secure them so be sure to use a trustworthy source when determining how much force is needed for installation purposes.
Johni-Bolt toilet bolts are made from quality steel and have been designed to last. In addition, they include safety locks that prevent them from being removed by children. It is important to replace toilet bolts every few years in order to avoid problems with leakage or separation once the toilet is replaced.
The best way to keep toilet bolts tight is to remove them when changing toilets. This will prevent any slop in the plumbing that could cause them to come loose.
To change toilets, first shut off the water supply at the street meter.
Rust has formed on the bolts in your tank as a result of years of condensation and water exposure. This rust is caused by oxidation, which occurs when iron, steel, or another metal comes into contact with water and oxygen over time. Metal toilets generally contain iron parts (bolts, springs, etc.) that are exposed to moisture in the air and liquid from accidents or normal use. These components will oxidize and turn rusty if they are not protected.
To prevent this corrosion from happening, you need to avoid exposing metal parts of your toilet to water. If an accident does cause water to contact these metals, then you should try to clean it up immediately. Use a non-acidic cleaner to remove any residue that may have formed due to the accident. You can also apply a protective coat every few years if you want to extend the life of your toilet.
If you leave your toilet bolt loose enough to rotate, then water will continue to leak out even after you've fixed the hole. This allows more time for water to contact the metal inside the bowl and increase the risk of corrosion. When replacing toilet bolts, make sure you get ones with lock washers and no rust on them. The locks serve to keep the bolts in place while still allowing them to be turned.
Remember that you cannot use another brand's tank with your Crane bowl. It's a Crane Galaxy tank. Most plumbing wholesale vendors should have these. If you don't find them in your local store, call or email the manufacturer directly.
If you replace a toilet tank with one from a different manufacturer, the tanks are unlikely to be interchangeable. Mismatched tanks and bowls cause issues such as hardware not aligning up and poor bowl balancing. Even if the bolts are perfectly aligned, the replacement tank may leak or be unsteady. Before you start any project, make sure that you use the right parts.
Kohler supplies most of its toilet tanks with holes for mounting them on a wall. However, some manufacturers seal their tank openings to prevent water damage. If you want to mount your new tank on a wall, you'll need to find another way to secure it. One option is to use a hanging kit sold by Kohler. These kits include special screws that fit into pre-drilled holes in the tank body. You can also buy self-drilling screws that will thread into any hole of a compatible size.
When replacing a toilet tank, always use the same type of tank as the original. This ensures that you get the best performance and reliability from your new toilet.
Kohler offers many years of quality service on its toilet tanks. When you purchase a new tank, it will come with detailed instructions on how to install it properly. Follow these instructions carefully to ensure that you get the best performance out of your new toilet tank.
Toilets are held in place by bowl-to-floor hardware, which fastens them to the floor or wall. These bolts, washers, and nuts go into mounting holes in the toilet's base. When the bolts are long enough to extend through the toilet base and into the flooring or wall, they give a firm grip. You may have to cut off any excess bolt with a hacksaw before it can be used.
The number of bolts needed depends on how deep they are drilled into the floor or wall. The holes should be large enough for the washer to fit inside but not so large that water can get in when you open the valve on the tank. Also, make sure that the bolts are spaced evenly around the toilet hole to prevent parts from becoming separated during installation.
Washers are used to distribute pressure over a larger area than just one hole would provide. They're also useful for preventing the bolts from coming out of the toilet base too easily. There are several different sizes of washers available, depending on the required amount of pressure against the toilet base.
Nuts are used to secure the ends of the bolts after they have been extended through the base of the toilet. They should be sized such as not to loosen under their own weight. Also, make sure that the threads on the nut match the thread type on the end of the bolt.